RFID Hotel Door Lock with Satin Stainless Steel and Gold PVD Finish

Hotel Door Lock System
RFID card entry with a keyed way in for staff
A slim stainless steel lock panel for hotel room doors. Guests open with an RFID key card, and the property keeps a keyed way in for staff and emergencies. One lock family covers both the satin stainless steel and gold PVD finishes used across the corridors.
- RFID card reader behind the black window
- Mechanical key override, 2 keys per lock
- Battery powered, no wiring in the door
What the lock does for the property
Each part of the lock answers a job that repeats every day on a hotel floor.
Tap-to-enter reader
The reader sits behind a sealed black window, so a guest taps a card instead of waiting at the desk. Cards are issued, extended and cancelled in the management software, which means a lost card is replaced in seconds, not by re-keying the door.
ANSI mortise and latch
The ANSI standard mortise carries the deadbolt and latch inside the door edge. A standard body means local locksmiths can service or replace it, and the door keeps a conventional hardware footprint instead of a proprietary cut-out.
Keyed override under cover
A brass mechanical cylinder hides behind the round cover below the lever. If a battery runs flat or a card is demagnetised at 2 a.m., a supervisor opens the door with the mechanical key and the guest never spends the night in the corridor.
Battery powered retrofit
Four AA alkaline batteries sit inside the back panel. Because nothing is wired through the door, an existing wooden or metal guest room door can be upgraded without chasing walls or adding low-voltage cabling to the corridor.
From check-in to room entry
Encode the card
Front desk software and a USB card encoder write the room number, validity window and access level onto the guest card.
Guest taps in
The card is read through the black window within a few centimetres and the mortise releases the latch.
Access expires itself
The card stops working at the check-out time written on it, so no one has to collect keys or change the lock between guests.
Staff use the key
For any situation a card cannot solve, the round cover lifts to expose the cylinder.
Where it fits
The panel is narrow enough for standard guest room doors and reads as quiet hardware rather than a control panel on the corridor wall.
- Business hotels and city hotels with high room turnover
- Resorts where salt air and humidity punish plated hardware
- Serviced apartments and long-stay units that need timed access
- Renovation projects replacing mechanical lever sets
Technical specification
| Material | Stainless steel |
|---|---|
| Finish | Satin stainless steel or gold PVD |
| Unlock method | RFID card and mechanical key |
| Card type | T5557 (125 kHz) or M1 (13.56 MHz) |
| Lock mortise | ANSI standard |
| Working voltage | DC 6V, 4 x AA alkaline batteries |
| Battery life | About 12 months in normal hotel use |
| Mechanical key | 2 pcs per lock |
| Door thickness | 38 mm to 52 mm |
| Reading distance | 0 cm to 3 cm |
| Panel style | Slim vertical panel, concealed key cylinder |
| Handle | Lever handle with round rosette |
| Application | Hotel, resort, serviced apartment |
What arrives in one set
Each set ships as a complete kit, so the installer opens one box per door instead of chasing missing parts on site.
Front panel, mortise lock body, mechanical cylinder with keys, side catch and fixing screws.
Buying notes for project teams
OEM service
Panel finish, logo and packing marks can follow the project spec, so the hardware matches the rest of the door package.
Management software
Room status, guest card issuing and staff card levels are handled from the front desk PC, with an encoder connected by USB.
Support after handover
Technical support continues after the locks are installed, which matters when a property runs the same locks for a decade.
Questions buyers ask before ordering
Will it read the cards we already use?
The reader is built for one card type and is fixed before production, so send us a sample or the card spec from the current system. Both low and high frequency options are on the shelf, which keeps the switch simple.
Can it replace our current mortise?
It fits doors from 38 mm to 52 mm thick with an ANSI footprint. Send the door edge photo and backset measurement with the enquiry and the matching body is confirmed before production.
How are the batteries replaced?
Batteries sit inside the back panel and are changed from inside the room by staff, without taking the lock off the door or opening the corridor side.
Silver or gold for the whole hotel?
Both finishes use the same panel and the same electronics, so a property can mix them by floor or wing without keeping two sets of spare parts.
Send the room count and door details
Tell us the number of rooms, door thickness and the card type in use, and we will confirm the lock configuration, encoder and card quantity for the project.
- *Title
- *Content
Email: dan@eproerlock.com
Mobile: +86 185 0752 5876
WhatsApp:+86 185 0752 5876
WeChat:185 0752 5876
- *Title
- *Content









